• 为您提供卷板机等产品。

新闻咨询

Great news
点击在线留言

联系人:张经理

手机:18637302099

邮箱:1311043454@qq.com

地址:新乡市牧野工业园区

新闻资讯
Great news
首页 > 三辊卷板机校准和运输

三辊卷板机校准和运输

发布时间:2016-05-16  文章来源:admin 点击次数:


  三辊卷板机属于机械类在运输当中我们要多加注意,在卷板机运输时必须高度小心,只能而且要装在封闭的卡车内或有盖帘的“开顶”集装箱内运输,不得暴露于尘土,雨雾或烟气当中。
  The three roller bending machine, belonging to the machinery in the transport of we must pay much attention to. In bending machine transport must be extremely careful, can and must be installed in the enclosed truck or cover curtain "truncated" container transport, shall not be exposed to the dust, rain and fog or smoke.
三辊卷板机
  1.机器必须放在厚木板上而且必须放置平稳(通常情况下,卡车底座状态良好是可能的),装载时必须将机器主机架放置在卡车底座上。
  1 the machine must be placed on a thick board and must be placed in a smooth (usually, the base of the truck is in good condition), and the machine must be placed on the base of the truck when it is loaded.
  2.如果机器是合为一体的,不要把任何东西放在机器上面、靠在上面或与机器的任何部分接触,机器必须放在卡车内的自由区域内。
  2 if the machine is in one place, do not put anything in the machine above, on or in contact with any part of the machine, the machine must be placed within the free area of the truck.
  3.机器的底座必须牢靠坚固,并牢牢地锚系住,防止在运输期间有任何移动。在运输过程中尽量避免急转弯、急刹车或强烈地震动等。
  The 3 machines must be firm and strong, tied firmly anchor, to prevent any movement during transportation. As far as possible in the transport process to avoid sharp turns, sudden brake or strong vibration, etc..
  4.对于遥控装置,因其装有非常容易损坏的电气和电子器件,移动或运输时要特别小心。
  4 for the remote control device, because it is equipped with a very easy to damage the electrical and electronic devices, mobile or transport to be particularly careful.
三辊卷板机
  当我们装好三辊卷板机时校准是不可缺少的,一般来说校准的方法为。拧紧螺栓,必要时用填隙片放在螺栓下面调节水平。用叉车或千斤顶只从承重梁两侧或承重梁本身的后面提起机器进行校平,不要靠到机器的其他任何部分。
  When we installed three roller bending machine calibration is indispensable, general calibration method. Tighten the bolts, when necessary shim on the bolt below regulation level. Use a forklift or a jack only from the side of the bearing beam or bearing beam itself behind the lifting of the machine for school level, do not rely on any other parts of the machine.
  1.机器必须用精密的水平仪沿两个轴向校平:
  1 the machine must be made with a precision level gauge with two axes:
  2.两个机架:检查他们彼此是否完全同相,为了完全同相,必要时使用填隙片(这是正确使用机器的必要条件)。
  2. The two frame: check their whether or not each other completely in phase, to completely in phase, when necessary use shims (this is necessary conditions for the proper use of the machine).
  3.在上压辊的纵轴:将水平仪放在上压辊的正中央,在马达箱/卡轭方向上
  The vertical axis 3 on the pressure roller: level and put it in the middle of the upper pressure roller, the motor yoke box / card direction
  4.在侧压辊的横向上:将水平仪放在两个压辊的两段靠近每个机架
  4 in the lateral side roller on the level gauge on the two roller two near each rack

  以上就是三辊卷板机的校准方法和卷板机运输的注意事项希望对大家有所帮助。
  The above is the three roller machine calibration method and machine transport considerations and I hope to help you.


  • 一键拨号
  • message
    短信咨询
  • map
    查看地图